Attenuation
Listado attenuation
-
00 in tensile strength 73 kg | 160 lb electrical performance: frequency attenuation (db/100 m) attenuation (db/100 ft) 30 mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz mhz regulatory compliance/certifications: agency classification rohs /eu compliant china rohs sj/t below maximum concentration value (mcv) iso designed, manufactured and/or distributed under this quality management systemall trademarks identified by ® or ™ are registered trademarks, respectively, of commscopecnt-400, cnt® 50 ohm braided coaxial cable, variable, black pe jacket product classification: brand cnt® product series cnt-400 product type braided coaxial cable construction materials jacket color black jacket material non-halogenated pe braid material tinned copper shield tape material aluminum dielectric material foam pe inner conductor material copper-clad aluminum wire dimensions: cable weight 00 kw shielding effectiveness >90 db velocity 85% product specifications; ©commscope, inc5 ft lb flat plate crush strength 010 kg/m diameter over dielectric mm | in diameter over jacket mm | in diameter over tape mm | in inner conductor od mm | in nominal size in outer conductor od mm | in electrical specifications: cable impedance 50 ohm capacitance 78com for the most current information0 pf/ft dc resistance, inner conductor ohms/km | ohms/kft dc resistance, outer conductor ohms/km | ohms/kft dc test voltage v jacket spark test voltage (rms) v maximum frequency ghz operating frequency band mhz peak power 16all specifications are subject to change without notice0 lb/in minimum bend radius, single bend mm | 1all rights reservedrevised: november page 1 of 2 february environmental specifications: installation temperature -40 °c to +85 °c (-40 °f to +185 °f) operating temperature -40 °c to +85 °c (-40 °f to +185 °f) storage temperature -70 °c to +85 °c (-94 °f to +185 °f) general specifications cable type cnt-400 braid coverage 90% braid brand cnt® mechanical specifications: bending moment 0
-
0 db tx noise suppression at rx frequency 90 db rx attenuation at tx frequency 90 db isolation tx to rx (min 5 mhz separation 75 db vswr (max) 1specifications tprd- frequency range mhz tx / rx separation (min) 5 mhz electrical specifications maximun input power 250 watts insertion loss (tx & rx to antenna) 1x 8? l dimensions (hwd) in5:1 temperature range -30°c to +70°c mechanical specifications number of cavities (4) - 4? dia5) mounting 19? panel connector termination n female finish gray acrylic enamel net weight lb25 x 19 x x 48 x 30
-
Features s50 microphone • professional side-address condenser microphone for vocals and instruments • provides excellent detail and clarity for capturing the nuances of vocals and acoustic instruments • class a fet design • cardioid polar pattern s30 microphone • professional pencil microphone for instruments and percussion • provides excellent definition and isolation for close mic’ing instruments, or clean ambience for distance mic’ing natural room reverberation specifications s50 microphone preamp: class-a fet polar patterns: cardioid frequency response: 30hz – 18khz high pass filters: n/a attenuation pad: n/a sensitivity: 5mv/pa maximum spl: 140db equivalent noise: typical load impedance: >500 ohms output source impedance: 200 ohms transformerless dimensions: 6perfect for any recording situation, the sp includes the s50 side address condenser microphone for vocals, the s30 pencil condenser microphone for instruments, or combine them for limitless recording possibilitiesoverview sterling audio’s sp recording microphone package provides professional sound quality and recording flexibility in a rugged, portable hard shell case2 oz power: phantom power
-
Volume control tracking: ±0,5db, 0db to -60db attenuation turn-on delay: 5 to 8 seconds phono preamplifier phono preamplifier equalization: riaa (± 0,25db) thd: imd: s/n ratio: > 80db below 10mv input reference at 1khz input sensitivity: 2,8mv for 2v output, 1khz input impedance: 47kohm, ±5%, 80pf overload: > 18mv at 20hz > 180mv at 1khz > 1,8v at 20khz general general pc: 21w maxfuncionado perfectamente con service hecho hace un mes con garantÃathe volume pot is a 32-step / fixed-resistors attenuator while the headphones is fed by the connected power amp's loop through, allowing direct speaker selection from the seventeen as welleven if discreetely, at least more so than pioneer or marantz, harman kardon was tops and chose to show its art not with more buttons, functions or displays but by remainig true to its name: citationoportunidad, preamplificador de la época de oro de harman kardon hecho en usareaction to square waves is exemplary and the phono stage is difficult to overloadhigh cut filter: -3db at 8khz, 12db/octlast preamplifier before the sale to beatrice food and subsequent departure of the us-built harman/kardonentradas para fono, aux, casetera, sintonizadorse puede probarespecificaciones técnicas y descripción tomadas de thevintageknobthe proeminent feature, the eq, uses broad slopes for its two extreme points (50hz and 8khz) to tailor the sound rather than correct it; active circuitry is useddimensions: 40,6 x 12 x 30,5cm weight: 9kgoutput amplifier output amplifier audio output: up to 14v rms into ohm or greater frequency response: below 5hz to beyond 125khz (±0,5db) below 3hz to beyond 270khz (-3db) square wave rise time: square wave tilt: less than 5% at 20hz thd: less than at 2v rms output imd: less than % at equivalent 2v rms output outputs: 2x headphones, 2x rec-out, 2x pre-out, 2x speaker pairs output impedance: less than 100 ohm load impedance: ohm or greater s/n ratio: 92db below 2v rms inputs: 3x aux, 2x tape, 2x phono, 1x tuner, 1x power amp feed-through input sensitivity: 200mv for 2v rms output input impedance: 20kohm subsonic filter: -3db at 20hz, 12db/oct
$ 13000