SENSOR MAGNETICO INALAMBRICO SHOCK APERTURA RF TX RX ALARMA EN SAN CRISTÓBAL-CAPITAL FEDERA

Bienvenidos a Xnet Argentina IMPORTANTE: Consultar antes de ofertar! Atencion al gremio y mayorista. Nos encontramos en CABA: Barrio Belgrano: Cabildo y Jose Hernandez. / Subte D, estación Jose hernandez. Barrio Flores: Nazca y Avellaneda. USD 50 Sensor Magnetico Inalambrico Shock Apertura Rf Tx Rx Alarma Kit sensor magnetico inalambrico generico 1rx 1tx shock + apertura Sirve para cualquier tipo de alarma! Si tiene una alarma vieja, y no quiere cablear los sensores, esta es la solucion. Receptor: 12v Transmisor : Pila aaa Package inlcuded: 1PCS Wireless Sensor ; 1 PCS DC12V 1 Channel relay receiver; 1 operating voltage: DC 12V ; 2 working frequency:433.92MHz; 3Maximum load: 1000 watts; 4PCB Size:41×20×15mm; 5 Momentary Mode ,Latch Mode , Toggle Mode can be adjustable by slodering back side. 6 Pls connect the receiver modules properly before power supply ; 8 Momentary Mode ,Latch Mode , Toggle Mode can be adjustable by jumper . 9 Pls connect the receiver modules properly before power supply ; 10 1 chanels; 11 Learning function (can works with EV1527 SC2262 PT2262 PT2264 PT2260 remote , can store 10 pcs different code remote ); Advantage : 1: Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 Learning remotes to re-learn; Output: A.singnal Inter-locking (Latch)connect 1 and 2 B.singnal Self-locking (Toggle) connect 2 and 3 C.singnal Non-locking (Momentary ) All disconnect Inter-locking (Latch): 4-way relay each other to switch, when relay A is working and locked , relay B C D corresponding to switch off; when B is working and locked , corresponding relay A C D swith off ; Only 1 relay is on among 4 relays A B C D; Non-locking type (Momentary): Press A and hold it , then A is on.Same as Relay B C D ; Self-lock type (Toggle): 4 chanels opens and closes independently, 4 chanels can work together ,they don’t affect each other . press A button, A relay of work and locked, press again then disconnected; Same as B C D . Learning method and steps 1. Keep pressing learnig key on receiver board , release the button when LED is off , enter the learning state ; 2. Press any key on remote control within 5 seconds , LED flash 3 times and then turn on , then it have success in learning . Clear the deposit information Keep Pressing Learning Key , LED turns off , Wait 10 Seconds , LED turn on , that deposited information has been successfully cleared ; Connect to Power supply : TB056 5 14 .jpg 433Mhz Wireless Door / Windown Sensor 1)Feature: It will work with most standard security system. Pull out the antenna of the magnetic detecto: when the door or window is opened from the closed position, LED 1 will turn to red for 2 seconds, the magnetic detector will be triggered and will send alarming signal to the main unit. Indication of low battery: When the voltage of battery is less than 7.5V, LED 2 will straightly turn on red light. At this time, you nee to immediately change the battery. TB212 3.jpg Launch Distance: 50-80 meters (open place) Operating Voltage: 12V Operating Frequency: 433MHz. Encoding: EV1527 Fixed Code IC Size: 71 x 36 x 15(mm) / 2.8 x 1.4 x 0.6(inch ) Oscillation resistance 470K Power supply: 12V 23A Battery (the battery is not included ) 2)Package: 1wireless door sensor Gracias por elegirnos Xnet argnetina